BSNL Broadband Error Codes & Description in DSL Technology

Some of the BSNL broadband connecting error codes were occurred with ADSL type technology via ADSL Modem when enabling the faster data transmission over copper telephone lines by using Bridge mode (or dialer mode), many of the customers are getting the Asymmetric digital subscriber line (ADSL) Broadband Line connecting error codes 619, 629, 631, 633, 645, 650, 651, 678, 680, 691, 718, 721 in frequent.

Every Broadband customer at least once enables in most frequent through DSL/ADSL Modem (CPE), To overcome this problems, we have already presented with some possible solutions in Broadband Services and now we are presented total broadband error codes as follows most occurred Broadband Error Codes with possible solutions.

BSNL DSL Broadband Line Connecting Error Codes in Detail

Error CodeBB Error Description
600An operation is pending.
601The port handle is invalid.
602The port is already open.
603Caller’s buffer is too small.
604Wrong information specified.
605Cannot set port information.
606The port is not connected.
607The event is invalid.
608The device does not exist.
609The device type does not exist.
610The buffer is invalid.
611The route is not available.
612The route is not allocated.
613Invalid compression specified.
614Out of buffers.
615The port was not found.
616An asynchronous request is pending.
617The port or device is already disconnecting.
618The port is not open.
619The port is disconnected.
620There are no endpoints.
621Cannot open the phone book file.
622Cannot load the phone book file.
623Cannot find the phone book entry.
624Cannot write the phone book file.m
625Invalid information found in the phone book.
626Cannot load a string.
627Cannot find key.
628The port was disconnected.
629The port was disconnected by the remote machine.
630The port was disconnected due to hardware failure.
631The port was disconnected by the user.
632The structure size is incorrect.
633The port is already in use or is not configured for Remote Access dialout.
634Cannot register your computer on the remote network.
635Unknown Error.
636The wrong device is attached to the port.
637The string could not be converted.
638The request has timed out.
639No Asynchronous net available.
640A NetBIOS Error has occurred.
641The server cannot allocate NetBIOS resources needed to support the client.
642One of your NetBIOS names is already registered on the remote network.
643A network adapter at the server failed.
644You will not receive network message popups.
645Internal  authentication Error.
646The account is not permitted to log on at this time of day.
647The account is disabled.
648The password has expired.
649The account does not have Remote Access permission.
650The Remote Access server is not responding.
651Your modem  (or other connecting device) has reported an Error.
652Unrecognized response from the device.
653A macro required by the device was not found in the device .INF file section.
654A command or response  in the device .INF file section  refers to an undefined macro
655The macro was not found in the device .INF file section.
656The macro in the device .INF file section contains an undefined macro
657The device .INF file could  not be opened.
658The device name in the device .INF or media .INI file is too long.
659The media .INI file refers to an unknown device name.
660The device .INF file contains no responses for the command.
661The device .INF file is missing  a command.
662Attempted to set a macro  not listed in device .INF file section.
663The media .INI file refers to an unknown device type.
664Cannot allocate memory.
665The port is not configured for Remote Access.
666Your modem  (or other connecting device) is not functioning.
667Cannot read the media  .INI file.
668The connection dropped.
669The usage parameter in the media  .INI file is invalid.
670Cannot read the section name from  the media  .INI file.
671Cannot read the device type from  the media  .INI file.
672Cannot read the device name  from the media .INI file.
673Cannot read the usage from  the media .INI  file.
674Cannot read the maximum connection BPS rate from  the media  .INI file.
675Cannot read the maximum carrier BPS rate from  the media  .INI file.
676The line is busy.
677A person answered instead of a modem.
678There is no answer.
679Cannot detect carrier.
680There is no dial tone.
681General Error reported by device.
691Access denied  because username and/or password is invalid on the domain.
692Hardware failure in port or attached device.
698A response keyname in the device .INF file is not in the expected format.
699The device response caused buffer overflow.
700The expanded command in the device .INF file is too long.
701The device moved to a BPS rate not supported by the COM driver.
702Device response  received when none expected.
707X.25 diagnostic indication.
708The account has expired.
709Error changing password on domain.
710Serial overrun Errors were detected while communicating with your modem.
711RasMan initialization failure. Check the event log.
712Biplex port is initializing. Wait a few seconds and redial.
713No active ISDN lines are available.
714Not enough ISDN channels are available to make the call.
715Too many Errors occurred because of poor phone line quality.
716The Remote Access IP configuration is unusable.
717No IP addresses are available in the static pool of Remote Access IP addresses.
718PPP timeout.
719PPP terminated by remote machine.
720No PPP control protocols configured.
721Remote PPP peer is not responding.
722The PPP packet is invalid.
723The phone number, including prefix and suffix, is too long.
724The IPX protocol cannot dial-out on the port because the computer is an IPX router.
725The IPX protocol cannot dial-in on the port because the IPX  router is not installed..
726The IPX protocol cannot be used for dial-out on more than  one port at a time.
727Cannot access  TCPCFG.DLL.
728Cannot find an IP adapter  bound to Remote Access.
729SLIP cannot be used unless the IP protocol is installed.
730Computer registration is not complete.
731The protocol is not configured.
732The PPP  negotiation is not converging.
733The PPP control protocol for this network protocol is not available on the server.
734The PPP  link control protocol terminated..
735The requested address was rejected by the server..
736The remote computer terminated the control protocol.
737Loopback detected..
738The server did not assign an address.
739The remote server cannot use the Windows NT encrypted password.
740The TAPI  devices configured for Remote Access failed to initialize or were not installed correctly.
741The local computer does not support encryption.
742The remote server does not support encryption.
743The remote server requires encryption.
744Cannot use the IPX  net number  assigned by the remote server. Check the event log.
752A syntax Error was encountered while processing a script.
BSNL Broadband Connecting Error Code List

With this total list of BSNL broadband error codes, you may find the reason and type of error when raised and can find the solution easily on searching or through contact to the concerned technician, and all the above broadband error codes were occurred in most times when enables for BSNL BRIDGE TYPE CONFIGURATION inside the modem, so it is recommended to avoid bridge mode since hacking and cracking the PC will also be easy.

Read This  Submit BSNL Go Green Request Online to Get your Bill Discount

Leave a Reply

Your email address will not be published. Required fields are marked *